Search found 180 matches

by Tech_Support
Thu May 18, 2017 12:27 pm
Forum: New Users' experiences
Topic: Constant Line On Waterfall In Every Frequency
Replies: 2
Views: 202

Re: Constant Line On Waterfall In Every Frequency

Hello, The RSP uses a zero IF architecture and the spur you are seeing results from residual DC offset in the I/Q signal paths. This is sometimes referred to as a 'centre spike'. It is rarely a problem, but it is important to ensure that your VFO is offset from this spike as the DC offset correction...
by Tech_Support
Thu May 18, 2017 8:00 am
Forum: General
Topic: ADS-B ob RSP 1?
Replies: 2
Views: 178

Re: ADS-B ob RSP 1?

Hello Steve,
SDRuno does not run on the Raspberry Pi, it is Windows only and it also does not decode ADS-B information. There is specific ADS-B software for the Raspberry Pi that is downloadable directly from our website.

Sincerely

SDRplay Tech_Support
by Tech_Support
Mon May 15, 2017 6:04 pm
Forum: SDR Antennas
Topic: Antenna ports
Replies: 4
Views: 236

Re: Antenna ports

Hello Paul,
Port B has worse low frequency roll-off when compared to port A because of the presence of the bias-T circuitry. This effect is present whether the bias-T is enabled or not.

Sincerely

SDRplay Tech_Support
by Tech_Support
Sun May 14, 2017 2:43 pm
Forum: General
Topic: Original SDRPlay
Replies: 6
Views: 436

Re: Original SDRPlay

Hello Gary,
Yes they will. The older style case comes apart by removing the ends. The case then separates into its two halves.

Sincerely

SDRplay Tech_Support
by Tech_Support
Sat May 06, 2017 7:26 am
Forum: New Users' experiences
Topic: RSP2 frustration on Mac
Replies: 28
Views: 3476

Re: RSP2 frustration on Mac

Hello Grantp,
The comment from g4jnw was in response to another post that we considered to be inappropriate and offensive an has since been deleted. It was not in reference to anything you wrote.

Sincerely

SDRplay Tech_Support
by Tech_Support
Fri May 05, 2017 4:26 pm
Forum: New Users' experiences
Topic: pov: "overflow" error
Replies: 2
Views: 638

Re: pov: "overflow" error

Uninstalling and re-installing SDRuno will not help. You need to reset the registry settings in SDRuno. This can be done from within SDRuno with the latest version of the software. Please note that you will lose all stored settings if you do this.

Sincerely

SDRplay Tech_Support
by Tech_Support
Thu Apr 27, 2017 6:37 pm
Forum: SDRplay related
Topic: Use SDR while transmitting
Replies: 17
Views: 3707

Re: Use SDR while transmitting

I don't know what power you transmit at, but 100W is +50 dBm, so 80 dB of isolation still gives you -30 dBm at the RSP input which is a very strong signal. The problem will be that the RF AGC will react to your Tx signal and will need to re-acquire the receive signal and this takes time. You could t...
by Tech_Support
Wed Apr 26, 2017 5:45 am
Forum: SDRuno
Topic: no hi-zched my antenna there with a 9:1 balun tried too witch it ied without anything there and stillon and nothing , tr
Replies: 1
Views: 195

Re: no hi-zched my antenna there with a 9:1 balun tried too witch it ied without anything there and stillon and nothing

Hello Gerald,
please make sure that your operating frequency is below 30 MHz. You can only select the Hi-Z port below 30 MHz.

Sincerely

SDRplay Tech_Support
by Tech_Support
Tue Apr 25, 2017 6:43 am
Forum: New Users' experiences
Topic: Audio cuts in and out
Replies: 5
Views: 428

Re: Audio cuts in and out

Hello Royce,
A more powerful CPU would certainly help.

Sincerely

SDRplay Tech_Support
by Tech_Support
Mon Apr 24, 2017 1:42 pm
Forum: SDRuno
Topic: Just downloaded SDR UNO 1.13
Replies: 10
Views: 681

Re: Just downloaded SDR UNO 1.13

Hello, There really should be no difference between SDRuno on your laptop and your desktop, unless you have them configured differently. Your best bet would be to open up a support ticket via: http://www.sdrplay.com/support/ Please include a detailed description of the problem along with screen shot...

Go to advanced search