Search found 413 matches

by Tech_Support
Sun Feb 17, 2019 7:39 pm
Forum: General
Topic: A CLOSE LOOK TO LOW COST NOISE GENERATORS
Replies: 19
Views: 377

Re: A CLOSE LOOK TO LOW COST NOISE GENERATORS

To all concerned, I sincerely hope that this thread does not descend into personal antagonism. If it does, I am afraid I will be forced to delete the entire thread. Please try to remain respectful and avoid all personal attacks, criticisms or insults. We are all here to help each other and everyone ...
by Tech_Support
Sun Feb 17, 2019 5:42 pm
Forum: SDRplay related
Topic: External clock RSPDuo and RSP2
Replies: 2
Views: 1649

Re: External clock RSPDuo and RSP2

Hello W1AMW,
No, this is a hardware limitation not software.

Sincerely

Tech_Support
by Tech_Support
Tue Feb 12, 2019 9:59 pm
Forum: Code Corner
Topic: Is SDRuno C++
Replies: 3
Views: 351

Re: Is SDRuno C++

Hello Mark,
SDRuno is not open source software. It is proprietary software and we don't release the source code to third parties under any circumstances.

Sincerely

Tech_Support
by Tech_Support
Tue Feb 12, 2019 9:00 pm
Forum: SDRplay related
Topic: No signal vhf rsp2
Replies: 6
Views: 356

Re: No signal vhf rsp2

Hello Whiteghost, The VHF & UHF band filters on the RSP2 go from 60-120 MHz, 120 - 250 MHz, 250 - 420 MHz and 420 -1000 MHz, So if you are getting signals at 120-132 MHz, then the second VHF band must be operational. You ask what has happened? I am afraid that is an impossible question to answer...
by Tech_Support
Tue Feb 12, 2019 12:58 pm
Forum: SDRplay related
Topic: No signal vhf rsp2
Replies: 6
Views: 356

Re: No signal vhf rsp2

Hello Whiteghost, Damage due to lightning will tend to affect all bands on the port affected and not just operation at VHF. Normal static is unlikely to damage the device as they are rated to 8kV. Static damage will never result in components appearing visually burned. This only occurs when sufficie...
by Tech_Support
Mon Feb 11, 2019 5:58 pm
Forum: SDRplay related
Topic: No signal vhf rsp2
Replies: 6
Views: 356

Re: No signal vhf rsp2

Hello Whiteghost,
Have you tried broadcast VHF FM? Perhaps you can post a screenshot?

Sincerely

Tech_Support
by Tech_Support
Sun Feb 10, 2019 8:38 pm
Forum: SDRplay related
Topic: Behavior of AM broadcast images in longwave spectrum?
Replies: 3
Views: 248

Re: Behavior of AM broadcast images in longwave spectrum?

Hello Franko
Try selecting Low IF mode. These are probably higher order mixing products as explained in this document:

https://www.sdrplay.com/docs/SDRplay_Op ... _MW_HF.pdf

Also, have you tried using the MW notch filter that is built into the RSPduo?

Sincerely

Tech_Support
by Tech_Support
Tue Feb 05, 2019 1:30 pm
Forum: General
Topic: Switching bug on the RF inputs of the RSPduo?
Replies: 2
Views: 247

Re: Switching bug on the RF inputs of the RSPduo?

Hello Glovisol, There is a bug which occasionally appears which can cause the effect that you describe. It will not be a fault with your hardware. We hope to correct this problem on the next release. We encourage anyone who finds any bugs to either contact support@sdrplay.com or open up a support ti...
by Tech_Support
Sun Feb 03, 2019 10:06 am
Forum: General
Topic: problem dump1090
Replies: 6
Views: 433

Re: problem dump1090

The discone should work fine if it is mounted correctly (outside and as high as possible). You will get much better performance if you build a simple multi-element co-linear antenna.

Sincerely

Tech_Support
by Tech_Support
Sat Feb 02, 2019 9:31 pm
Forum: General
Topic: problem dump1090
Replies: 6
Views: 433

Re: problem dump1090

I suggest that you open a support ticket via www.sdrplay.com/support

Please provide details of the software that you have installed, what OS you are using, how you run the software and exactly what you see. Ideally, please provide screen shots.

Sincerely

Tech_Support

Go to advanced search