Search found 84 matches

by Mike2459
Wed Sep 19, 2018 12:33 pm
Forum: SDR Antennas
Topic: Wellbrook ALA1530LN
Replies: 5
Views: 106

Re: Wellbrook ALA1530LN

Thanks Paul
I thought perhaps it was an electronic fuse. I have one of these on a supply for a Mini Whip. In order to reset it after an overload, I must power it down and turn it back on.
by Mike2459
Wed Sep 19, 2018 11:09 am
Forum: New Users' experiences
Topic: Can I get Meteor m2 with RSP1a and SDRuno
Replies: 3
Views: 39

Re: Can I get Meteor m2 with RSP1a and SDRuno

You need an old version of SDRSharp, version 1361 or earlier, the newer versions will not support the ExtIO plugin which is available here in the downloads section of this site. Also the demod and tracker plugin you need must be the DotNet 3.5 version. The old SDRSharp 1361 is here: https://www.qsl....
by Mike2459
Wed Sep 19, 2018 9:44 am
Forum: SDR Antennas
Topic: Wellbrook ALA1530LN
Replies: 5
Views: 106

Re: Wellbrook ALA1530LN

Paul: What is the procedure for resetting the built-in fuse? Or, does it require replacement if it trips?
by Mike2459
Wed Sep 19, 2018 9:27 am
Forum: New Users' experiences
Topic: Can I get Meteor m2 with RSP1a and SDRuno
Replies: 3
Views: 39

Re: Can I get Meteor m2 with RSP1a and SDRuno

2018-9-12-9-24-23-790_122.RGB122 copy.jpg Hurricane Florence from Meteor M2 using RSDRPlay RSP2, Homebuilt QFH Antenna, SDRSharp v1361 w/realtime Meteor QPSK plugin & DDE tracking plugin (for Doppler correction), and Orbitron for Sat tracking and doppler. The RSP2 works much better than a dongl...
by Mike2459
Mon Sep 17, 2018 2:08 am
Forum: SDRuno
Topic: SDRuno Software Issue
Replies: 6
Views: 606

Re: SDRuno Software Issue

In SDRUno 1.22/1.23:
In the RX Control Panel:
Right click inside the frequency display area.
The Tuning Step Popup will open.
Left click on the desired Step.

The current frequency step is displayed in the upper left corner of the frequency display window.
by Mike2459
Mon Sep 10, 2018 12:20 am
Forum: New Users' experiences
Topic: Absolutely Green New User
Replies: 5
Views: 608

Re: Absolutely Green New User

Are you sure of entering the correct frequency? An FM broadcast on say 105.5 FM will be entered in SDRUno as 105500000, 1220AM as 1220000. Also use the correct mode AM, FM etc and bandwidth for the signal you are hearing. You should be able to hear and see signals on the spectrum display on the AM o...
by Mike2459
Sun Sep 09, 2018 10:53 pm
Forum: General
Topic: Beginner's curiosity
Replies: 5
Views: 371

Re: Beginner's curiosity

PPS: It appears SB on 353 khz uses an unmodulated carrier, or ON-OFF keying.
by Mike2459
Sun Sep 09, 2018 10:44 pm
Forum: General
Topic: Beginner's curiosity
Replies: 5
Views: 371

Re: Beginner's curiosity

PS: When using the ClassAxe Database if you don't know the call simply enter the frequency in khz in the freq field. It will list all NDB's using that frequency (and several Khz above the entered freq in ascending order)
by Mike2459
Sun Sep 09, 2018 10:25 pm
Forum: General
Topic: Beginner's curiosity
Replies: 5
Views: 371

Re: Beginner's curiosity

Hi Paul: I am in the USA so I can't receive any ndb's from Europe. Here is the info I found on the Horta NDB. Carrier freq: 380 Call: FIL LSB:1017 USB:1024 Period:13.6 Details:ID+10" gap Loc:Horta / Faial Island AZR Gridsquare of TX: HM58pm The LSB & USB fields show the modulation frequency...
by Mike2459
Sat Sep 08, 2018 9:44 pm
Forum: New Users' experiences
Topic: New RSP2pro - Dissapointing Results
Replies: 4
Views: 703

Re: New RSP2pro - Dissapointing Results

Some of these RSP2pros had internally reversed A & B port connections. That is, the A input connector is internally connected to the B port and vice-versa. I have also noticed that strong signals can bleed over into the unused antenna input.

Go to advanced search