Search found 675 matches

by sdrplay
Sun Feb 18, 2018 2:18 pm
Forum: SDRuno
Topic: Does SDRuno Software Allow For Continuous Tuning ?
Replies: 18
Views: 267

Re: Does SDRuno Software Allow For Continuous Tuning ?

Also, please note that port A and B of the RSP2 are only spec'd down to 1.5 MHz - if you want to get good performance at VLF, you are better using the HiZ port.

Best regards,

SDRplay Support
by sdrplay
Sun Feb 18, 2018 2:16 pm
Forum: SDRuno
Topic: Does SDRuno Software Allow For Continuous Tuning ?
Replies: 18
Views: 267

Re: Does SDRuno Software Allow For Continuous Tuning ?

You have a sample rate of 2MHz and a decimation of 8 which gives you a total sample rate of 250kHz and the IF bandwidth is set to 200kHz. The LO is set to 342kHz, so you are just seeing the edge of the IF filter rolloff.

Looks normal to me.

Best regards,

SDRplay Support
by sdrplay
Sun Feb 18, 2018 9:25 am
Forum: SDRuno
Topic: Does SDRuno Software Allow For Continuous Tuning ?
Replies: 18
Views: 267

Re: Does SDRuno Software Allow For Continuous Tuning ?

I just tried to look at the link, but got a page not found message.
by sdrplay
Sun Feb 18, 2018 9:20 am
Forum: Code Corner
Topic: CubicSDR 0.2.3 released. How about updating links???
Replies: 7
Views: 320

Re: CubicSDR 0.2.3 released. How about updating links???

We provide the same support on non-Windows platforms as we have ever done. We have always maintained the API for developers to use on Windows, Mac, Linux, ARM and Android. We support SoapySDR which is cross platform and recently gr-osmosdr has been updated, which again is cross platform. CubicSDR is...
by sdrplay
Sat Feb 17, 2018 2:48 pm
Forum: SDRuno
Topic: Does SDRuno Software Allow For Continuous Tuning ?
Replies: 18
Views: 267

Re: Does SDRuno Software Allow For Continuous Tuning ?

If you are using a RSP, then the LO can tune between VLF and 2GHz without the need to press Stop/Start - if you are using other hardware with the ExtIO version of SDRuno, you will need to check with the hardware manufacturer on what their product allows/requires.

Best regards,

SDRplay Support
by sdrplay
Fri Feb 16, 2018 8:47 pm
Forum: Code Corner
Topic: CubicSDR 0.2.3 released. How about updating links???
Replies: 7
Views: 320

Re: CubicSDR 0.2.3 released. How about updating links???

I've just read through this thread and I'm confused as to what the issue is. CubicSDR is open source software and not ours. We provide builds on an ad-hoc basis for Mac because I was asked to provide them when I can. You'll note the for other OS platforms we just link to CubicSDR.com and reference t...
by sdrplay
Fri Feb 16, 2018 8:41 pm
Forum: New Users' experiences
Topic: RSP1 vs RSP1A using SDR Console V3
Replies: 3
Views: 61

Re: RSP1 vs RSP1A using SDR Console V3

The image on the right is with a RSP1, the Main Window is not right for RSP1A

Please also show the spectrum, as that will show the relationship of the LO to the VFO

Best regards,

SDRplay Support
by sdrplay
Tue Feb 13, 2018 1:57 am
Forum: General
Topic: Doppler tracking with SATPC32
Replies: 1
Views: 89

Re: Doppler tracking with SATPC32

SDRuno will operate like a Kenwood TS-480 for CAT control.

Best regards,

SDRplay Support
by sdrplay
Tue Feb 06, 2018 2:01 am
Forum: New Users' experiences
Topic: Tuning on SDRplay Pro2
Replies: 2
Views: 167

Re: Tuning on SDRplay Pro2

Hello John, The bar tells you which digit will be affected when you use the mouse scroll wheel. Clicking will put you into direct frequency entry and then you can either type the frequency in or use the keypad in the RX control panel. You can use escape to leave the frequency entry if you want to. R...
by sdrplay
Sun Feb 04, 2018 9:08 pm
Forum: SDRplay related
Topic: Linux SoapySDR cannot find sdrplay modules
Replies: 11
Views: 296

Re: Linux SoapySDR cannot find sdrplay modules

If it's in your ~/.bashrc file then it should be picked up all the time. You may want to log out or reboot for it to take effect.

Best regards,

SDRplay Support

Go to advanced search