Search found 15 matches

by VE9DAN
Mon Jun 10, 2019 6:42 pm
Forum: Spectrum Analysis
Topic: Calibration Using CHU
Replies: 5
Views: 2533

Re: Calibration Using CHU

Yes Mike, I see what you are doing.
I'll play with it tonight and get back to you.
Dan
by VE9DAN
Mon Jun 10, 2019 5:55 pm
Forum: Spectrum Analysis
Topic: Marker A, PPM Trim, and FMT
Replies: 2
Views: 1591

Re: Marker A, PPM Trim, and FMT

Yes I agree Mike.
So try aligning any Marker you choose with the calibrated signal, and paste your screenshot.
I tried but couldn't do it.

I want to see Marker D showing the exact frequency ... and read how you did it.
Play with CHU and WWV ... any frequency.
Dan
by VE9DAN
Mon Jun 10, 2019 10:13 am
Forum: Spectrum Analysis
Topic: Marker A, PPM Trim, and FMT
Replies: 2
Views: 1591

Marker A, PPM Trim, and FMT

Using RSP 1 and Version 1.0, tuned to 3.330 CHU. I have 3 markers following the peaks. I am set at a 10 KHz span and Averaged. PPM is set fairly high at +1.9. Marker A is set on the carrier frequency of 3.330 MHz. Here is what I noticed: 1) Marker A doesn't Refresh like B and C do. Marker A lays dor...
by VE9DAN
Mon Jun 10, 2019 8:22 am
Forum: Spectrum Analysis
Topic: 144 MHz In The Woods
Replies: 0
Views: 1319

144 MHz In The Woods

I am using an RSP 1 and Version 1.0 of the Analyzer. I am tuned to 144 MHz, 10 KHz span, and Averaged waveforms. I live in the woods alongside a beach and am remote from local interference. I see two unspeakable peaks. Neither peak is spot on any particular frequency. Their difference is 951 Hz. Are...
by VE9DAN
Mon Jun 10, 2019 7:01 am
Forum: Spectrum Analysis
Topic: Calibration Using CHU
Replies: 5
Views: 2533

Re: Calibration Using CHU

Very good. You have to explain to me how you were able to post the screenshots. I see you are 2 Hz low on the carrier, and 3 Hz low on the beeps. Can you please try using the ppm setting on the lower right hand side of the screen to adjust the marker frequencies ... just to see if you can get the tw...
by VE9DAN
Sun Jun 09, 2019 9:13 pm
Forum: Spectrum Analysis
Topic: Calibration Using CHU
Replies: 5
Views: 2533

Calibration Using CHU

Please have a look at the attached screenshot from my spectrum analyzer. Version 1.0 I am measuring the two frequencies transmitted by CHU. One is the carrier freq of 7.850 and I am reading it 6 Hz lower than I should be. The second freq CHU transmits are the beeps and they set it 1,000 Hz higher. I...
by VE9DAN
Mon Mar 25, 2019 1:47 pm
Forum: SDRuno
Topic: Does Anyone Use the Recording Feature?
Replies: 3
Views: 1592

Does Anyone Use the Recording Feature?

Typically, if I want to record something, I only want to record what I am hearing. I don't want to record everything else.
If some of you use the Recording Feature in Uno, please explain HOW you use it.
by VE9DAN
Tue Mar 19, 2019 4:56 pm
Forum: SDRuno
Topic: Scanning the 2M Ham band
Replies: 7
Views: 2794

Re: Scanning the 2M Ham band

Hugo ...

Your -60 threshold setting seems pretty high. You will miss signals I would think.
I run my threshold anywhere from -90 (HF) to -110 (VHF).
I like scanning the Aero frequencies for Gander, NFLD, New York, and Santa Maria.
by VE9DAN
Mon Mar 18, 2019 11:49 pm
Forum: SDRuno
Topic: SDRuno Decoding Stuff Automatically...and Magic Boy
Replies: 0
Views: 1011

SDRuno Decoding Stuff Automatically...and Magic Boy

Now this may be a bit extreme. Whatif SDRuno could decode FT8, RTTY, PSK31. CW, JS8Call, Contestia, and say Olivia 16/500 ... perhaps in a pop-up window. I click on a CW signal, and a magic window pops up to decode it. I click on another CW signal, the window stays, and decodes. I close the CW digit...
by VE9DAN
Mon Mar 18, 2019 11:03 pm
Forum: SDRuno
Topic: V 1.3 ...W10 .. Recording With a Schedule
Replies: 1
Views: 767

V 1.3 ...W10 .. Recording With a Schedule

Love V 1.3 ... haven't tried the 2 monitor thing yet. Even though I have them. I tend to use second monitor for other things. But, here is an issue we all have to tolerate. When we record, we are obligated to record the entire spectrum. For an hour long program, that simply means many GB's consumed ...