Search found 195 matches

by DanubeBCL
Sun Aug 07, 2016 1:04 pm
Forum: SDRuno
Topic: Increasing USB bandwidth
Replies: 5
Views: 4255

Re: Increasing USB bandwidth

There is limitation because for SSB 12kHz is over enough. Well, one can see things different. WiNRADiO allows 64 kHz (!) USB bandwidth in the G3xDDC models. ELAD allows 24 kHz, same as SDRConsole. Sometimes this can be useful decoding certain digital modes. Other SDRs alas only allow 3.6 or maybe 7...
by DanubeBCL
Thu Aug 04, 2016 6:05 pm
Forum: SDR Antennas
Topic: Need help with Wellbrook Loop & SDRplay/SDRuno
Replies: 6
Views: 8123

Re: Need help with Wellbrook Loop & SDRplay/SDRuno

Sorry to say this. But the simple two frontend filters 0 - 12 MHz and 12 - 30 MHz are not enough to unburden the Mirics tuner from strong signals. This is a matter of cost and effort. A Funcube pro+, which has more filter sections, also has problems to cope with strong outband signals. And even mid ...
by DanubeBCL
Thu Aug 04, 2016 9:16 am
Forum: SDR Antennas
Topic: Magnetic Loop Antenna with SDRPlay
Replies: 9
Views: 15400

Re: Magnetic Loop Antenna with SDRPlay

"Degen style" antennas (or tuned high impedance loops) are certainly not a bad choice for portable operation at low power (batteries). For fixed installation a wideband loop covering 10 kHz ... 30/60 MHz should be preferred. You can put it in your garden (hopefully) as far away from neighb...
by DanubeBCL
Sun Jul 31, 2016 9:13 am
Forum: SDRplay related
Topic: FLDIGI only partial waterfall.
Replies: 5
Views: 5442

Re: FLDIGI only partial waterfall.

Yes, you are right. The squelch sometimes spoils decoding. I also have forgotten many times to watch the slider ;-).
BTW: 80 Hz or 85 Hz is not the problem. I believe it should be 82 Hz, but this is all within tolerance.
73, Heinrich
by DanubeBCL
Fri Jul 29, 2016 7:27 pm
Forum: SDRplay related
Topic: FLDIGI only partial waterfall.
Replies: 5
Views: 5442

Re: FLDIGI only partial waterfall.

Hello Wolfgang, sorry that I cannot help. This station works with SDRuno, HDSDR, wherever the sound comes from (maybe even from the Dutch WebSDR). My settings are: Carrier shift 80 Hz (custom) Baud rate 50 Baudot 5N1.5 Revers "Rv" in the main window clicked (because I am using USB resp. DI...
by DanubeBCL
Thu Jul 21, 2016 9:37 am
Forum: SDRuno
Topic: SDRuno Settings with K3 IF
Replies: 4
Views: 6548

Re: SDRuno Settings with K3 IF

Is there a way to have the DC Spike offset from my tuned frequency Hi, you only can click into the waterfall/spectrum window next to the center. Then every tuning will take place with an offset and you can avoid the center soundcard spike. But at next start SDRuno returns to the center and you are ...
by DanubeBCL
Tue Jul 19, 2016 2:03 pm
Forum: SDRplay related
Topic: Digital Modes
Replies: 4
Views: 11469

Re: Digital Modes

After reading another message here about fldigi referring to this post I came upon section 6 In HDSDR, click on SOUNDCARD and then RX INPUT FROM RADIO. Change this to match the setting you selected in your digital mode software. You should not change the RX Input from Radio. This must remain your ra...
by DanubeBCL
Tue Jul 19, 2016 12:25 pm
Forum: SDRplay related
Topic: FLDIGI only partial waterfall.
Replies: 5
Views: 5442

Re: FLDIGI only partial waterfall.

Hello, fldigi just "listens" to any sound at the soundcard you have selected in fldigi Configure, Sound Card, Capture. As long as you can hear uninterrupted sound from your HDSDR, fldigi should "hear" the same uninterrupted sound. I am using VB Audio Hi-Fi Cable as a default soun...
by DanubeBCL
Sat Jul 16, 2016 5:39 pm
Forum: SDRuno
Topic: SDRUno CAT problem
Replies: 5
Views: 6046

Re: SDRUno CAT problem

Hello Paul, your FT2000 must be connected to a physical COM port on your PC where Omnirig is runnning. It seems as if you are trying to access the FT2000 through an uRouter network. I do not have such a setup and cannot comment on uRouter. But, when Omnirig Client.exe finds the FT2000 and reports fr...
by DanubeBCL
Fri Jul 15, 2016 11:51 am
Forum: SDRuno
Topic: SDRUno CAT problem
Replies: 5
Views: 6046

Re: SDRUno CAT problem

In order to control your FT2000 you do not need VSPE. Install Omnirig. The rest of the procedure is described in the SDRuno manual. In short: Go to MAIN window, SETT., ORIG and check if your FT2000 is on-line. Then go to RX CONTROL window, SETT., ORIG and select what direction you want to control (V...

Go to advanced search