Search found 144 matches

by Paul
Thu Nov 30, 2017 10:02 am
Forum: SDRuno
Topic: Old to RSP1, new to SDRuno, need help!
Replies: 6
Views: 1033

Re: Old to RSP1, new to SDRuno, need help!

OK, I'll take a shot at some of your questions..... If you are using version 1.21, that may be the same issue I have encountered and reported on an open support ticket. It has happened to me twice but I have not found a way to duplicate it at will. The software acts as though the LO is locked even ...
by Paul
Wed Nov 29, 2017 9:12 am
Forum: SDR Antennas
Topic: Antenna port limitations
Replies: 1
Views: 835

Antenna port limitations

Having had the RSP2 for a whiie now and achieved generally pretty satisfactory results with the antenna setup that is possible/practicable for me at present, which is: Longwire on the Hi-Z Port, H/V/UHF Discone (with some HF capability) on Port B and an active mini-whip on Port A. Whilst I note that...
by Paul
Sun Nov 26, 2017 8:00 am
Forum: General
Topic: RSP2Pro, SPRUno, and the Mac
Replies: 2
Views: 461

Re: RSP2Pro, SPRUno, and the Mac

Although primarily a Mac user, I use a PC for SDRuno and the RSP2. However, the link below takes you to the SDRplay downloads page where the necessary software to run them on a Mac is located. https://www.sdrplay.com/downloads/ I understand that it can be run successfully using Cubic, although some ...
by Paul
Sat Nov 25, 2017 2:01 pm
Forum: SDRuno
Topic: New User Problems
Replies: 18
Views: 3329

Re: New User Problems - frequency entry

Please note that there is a "." top left on the uno keypad and "mhz" top right.
So, enter whole Mhz - tap dot - complete entry - tap Mhz.
It is in the revised manual....
by Paul
Mon Nov 20, 2017 12:17 pm
Forum: General
Topic: NDB reception
Replies: 12
Views: 2673

Re: NDB reception

Hi 13dka Thanks for all the information. Were I to "sacrifice" the HI-Z port to achieve the best LF/mf signal on the mini-whip (which definitely outperforms my simple end-fed long-wire in this area), I would disadvantage myself with respect to reception on the long wire (9:1 balun in line)...
by Paul
Sun Nov 19, 2017 5:06 pm
Forum: SDRuno
Topic: Scanner?
Replies: 20
Views: 2784

Re: Scanner?

Just for the record; I tried the RSP2 and EXTIO version with the SDR# revision 1361, which ran as advertised (when I finally cornered a copy). However, I was unable to locate the Frequency Manager plug-in that works with this version, so abandoned this route. Happy for now to wait for the real deal,...
by Paul
Sun Nov 19, 2017 9:22 am
Forum: General
Topic: NDB reception
Replies: 12
Views: 2673

Re: NDB reception

Hi Andy Thanks for all the useful advice re NDB reception. Did a bit of antenna "fettleing," replacing the RAS0Ms mini-whip on port A with another version from the Ukraine (I doubt my ability to make my own) and using it on Port A, I am now able to get pretty good NDB reception (mainly usi...
by Paul
Sat Nov 18, 2017 7:00 pm
Forum: SDRuno
Topic: Scanner?
Replies: 20
Views: 2784

Re: Scanner?

Hi there If it would be of any assistance to you in coming to a decision, both the RSP1 and apparently the RSP1A are able to scan using the well-thought of and featured SDR# programme, which is available as a plug-in via the downloads section of the SDRplay website - see: http://www.sdrplay.com/down...
by Paul
Wed Nov 15, 2017 11:04 am
Forum: SDRuno
Topic: SDRuno 2.1
Replies: 2
Views: 698

Re: SDRuno 2.1 - bit of a wait for this one?

Sorry - dyslexia
Thanks very much for all the hard work with the latest 1.21 version and all the hard work involved in such a short time frame -much appreciated.
If I can't even get the version right what hope is there?
by Paul
Tue Nov 14, 2017 4:01 pm
Forum: SDRuno
Topic: SDRuno 2.1
Replies: 2
Views: 698

SDRuno 2.1

Thanks for all the hard work and the "roadmap."

Go to advanced search