Search found 318 matches
- Fri Jun 07, 2019 3:39 pm
- Forum: SDRuno
- Topic: Feature request
- Replies: 4
- Views: 42917
Re: Feature request
The step sizes can be changed by a right click in the RX window while hovering over the frequency digits. A menu will open with many choices. I tried this a moment ago, made some changes, closed SDRUno, reopened it, the changes appear to be saved. They were stored to the ini file. They may be lost i...
- Fri Jun 07, 2019 3:01 pm
- Forum: New Users' experiences
- Topic: Spurious signals with no antenna
- Replies: 3
- Views: 38877
- Sat Jun 01, 2019 3:48 pm
- Forum: SDR Antennas
- Topic: New Sdrplay and antenna creation
- Replies: 21
- Views: 128836
Re: New Sdrplay and antenna creation
You would then need an SDR that could handle the increased dynamic range, the SDRPlay class cannot.If the above is the theory of the workings of this antenna, then a bigger capacitor will have a bigger aperture and couple more "E" field, thus more signal to the receiver.....
- Fri May 31, 2019 10:44 pm
- Forum: Spectrum Analysis
- Topic: Can’t start tracking generator
- Replies: 5
- Views: 45704
Re: Can’t start tracking generator
Today I connected the tracking generator to my scope. Tried all the functions with Arduino serial monitor. Set up a sweep and observed it on the scope. I could not get a response for the Connect command. Could this be the issue with Spectrum Analyzer? According to the user manual the tracking genera...
- Fri May 31, 2019 7:52 pm
- Forum: General
- Topic: Spectrum analyzer Vs. SDRuno. What’s the primary differences?
- Replies: 5
- Views: 20802
Re: Spectrum analyzer Vs. SDRuno. What’s the primary differences?
Spectrum Analyzer is primarily test and measurement software. It's particularly helpful in the characterization and design of RF filters.
- Fri May 31, 2019 2:37 am
- Forum: Spectrum Analysis
- Topic: Can’t start tracking generator
- Replies: 5
- Views: 45704
Re: Can’t start tracking generator
Thank you, Bob.
Got a response to the version command with serial monitor. 'Newline' or 'No line ending' must be selected in the drop down box in serial monitor.
'Carriage return' or 'Both NL & CR' won't get a response.
Got a response to the version command with serial monitor. 'Newline' or 'No line ending' must be selected in the drop down box in serial monitor.
'Carriage return' or 'Both NL & CR' won't get a response.
- Wed May 29, 2019 10:34 pm
- Forum: SDR Antennas
- Topic: New Sdrplay and antenna creation
- Replies: 21
- Views: 128836
Re: New Sdrplay and antenna creation
Bas, I took your advice - compared the two G5RV's (yours and Hackgreens) and the Twente sdr : http://websdr.ewi.utwente.nl:8901/ which uses a miniwhip. I'm not going to make any further comments. Make the comparison for yourself and report back.
- Wed May 29, 2019 10:06 pm
- Forum: Spectrum Analysis
- Topic: Can’t start tracking generator
- Replies: 5
- Views: 45704
Re: Can’t start tracking generator
Bob:
There was a discussion about this a few weeks ago here:. https://www.sdrplay.com/community/viewt ... =12&t=4336
You've made more progress than I. I can't get the mega2560 to answer when I query it with the serial monitor. Rx flashes but no TX.
Mike
There was a discussion about this a few weeks ago here:. https://www.sdrplay.com/community/viewt ... =12&t=4336
You've made more progress than I. I can't get the mega2560 to answer when I query it with the serial monitor. Rx flashes but no TX.
Mike
- Mon May 27, 2019 8:42 pm
- Forum: SDRuno
- Topic: Memory Files missing?
- Replies: 2
- Views: 12057
Re: Memory Files missing?
There are no s1b files included in an SDRUno download.
- Sun May 26, 2019 4:12 am
- Forum: New Users' experiences
- Topic: Greetings - and issue with CW buzz
- Replies: 1
- Views: 32378
Re: Greetings - and issue with CW buzz
If you have an AC voltmeter measure the AC between the chassis of your SDR (when it's connected to the PC and the PC is running) and (with the antenna disconnected from the SDR) the shield of your antenna cable. You may be surprised what you find. I was. I measured 60 Volts AC