See pm also.
I hope SDRPlay will fix the issue soon.
73, Heinrich
Search found 203 matches
- Mon Dec 26, 2016 5:13 pm
- Forum: SDRuno
- Topic: SDRunoExtIO no longer starts
- Replies: 15
- Views: 37291
- Mon Dec 26, 2016 4:26 pm
- Forum: SDRuno
- Topic: SDRunoExtIO no longer starts
- Replies: 15
- Views: 37291
Re: SDRunoExtIO no longer starts
See pm here in the board, Gerard.
73, Heinrich
73, Heinrich
- Mon Dec 26, 2016 10:26 am
- Forum: SDRuno
- Topic: SDRunoExtIO no longer starts
- Replies: 15
- Views: 37291
Re: SDRunoExtIO no longer starts
Please, can you tell me where to find the old dll or the 1.11 version of SDRUNO Hello Gerard, I re-installed version 1.11, made a copy of all the files in the installation directory and the installed 1.12 again. Then I copied the WRPnfdc.dll from the old installation. But I have no clue if the new ...
- Sat Dec 24, 2016 1:10 pm
- Forum: General
- Topic: SAQ Christmas Transmission with RSP1
- Replies: 2
- Views: 9830
Re: SAQ Christmas Transmission with RSP1
You also have these strange signals around 16 kHz and 18 kHz, Wolfgang. I have already suspected toys from my neighbours. But they seem to be "real" as you have them, too. That on 18 kHz seems to be weaker at your location. Maybe there are similar electronics in households near you. Don't know: Phot...
- Fri Dec 23, 2016 5:14 pm
- Forum: New Users' experiences
- Topic: High noise floor on RSP2??
- Replies: 5
- Views: 18320
Re: High noise floor on RSP2??
If I understood it right the noise level rises when any kind of antenna is connected: Bonito MiniWhip or simple random wire. Then I should say the noise level in and around your house is high. a) Are the antennas far away enough from PCs and monitors? b) Does the receiver have a good ground connecti...
- Fri Dec 23, 2016 4:40 pm
- Forum: SDRuno
- Topic: SDRunoExtIO no longer starts
- Replies: 15
- Views: 37291
Re: SDRunoExtIO no longer starts
After several trials and errors I found out the follwowing: SDRuno 1.12 copies a WRPnfdc.dll dated 02/12/2016 13:46. SDRunoExtIO does NOT start with this dll. SDRuno uses a WRPnfdc.dll dated 24/10/2016 18:33. SDRunoExtIO starts OK with this dll. When I copy this old dll to the new 1.12 installation ...
- Fri Dec 23, 2016 4:28 pm
- Forum: SDRuno
- Topic: SDRunoExtIO no longer starts
- Replies: 15
- Views: 37291
SDRunoExtIO no longer starts
After installing SDRuno 1.12 I cannot start SDRunoExtIO any more. The programme terminates before anything is shown.
No problem when I go back to 1.11.
Has anyone got a similar problem? What could I have messed up?
73, Heinrich
No problem when I go back to 1.11.
Has anyone got a similar problem? What could I have messed up?
73, Heinrich
- Tue Dec 20, 2016 10:49 am
- Forum: SDRuno
- Topic: Antenna Referred Power Measurement.
- Replies: 9
- Views: 26802
Re: Antenna Referred Power Measurement.
To David, to avoid being off topic too much I try a short answer: In Europe the powerline modems (PLT, PLC, dLAN, powerLAN etc.) have been generously allowed at high noise levels due to intensive "work" of the industry lobbyists at the European Parliament, using up to 105 dBµV broadband power on uns...
- Mon Dec 19, 2016 5:21 pm
- Forum: General
- Topic: Continuing Difficulties trying to run SDRUno with HRD
- Replies: 2
- Views: 13638
Re: Continuing Difficulties trying to run SDRUno with HRD
HDSDR and HRD communicate with each other: HDSDR has a built in customized DDE data exchange interface which is understood by HRD and vice versa. You do not need Omnirig for this at all. HRD controls the FT-857 through COM port 5 and HRD controls HDSDR by DDE (and vice versa). SDRuno does not have t...
- Sat Dec 17, 2016 6:42 pm
- Forum: SDRuno
- Topic: Antenna Referred Power Measurement.
- Replies: 9
- Views: 26802
Re: Antenna Referred Power Measurement.
Well David, there are certainly "better" SDRs with higher direct sampling rates and so on, but I have given up to look for new SDR receivers. The ones I own (Perseus, G33DDC, Anan Angelia, apart from the toys like Funcube, RSP1 or RTL dongles) were expensive enough and it makes no sense for me to hu...