I may be being naive, but I see no mention of the Cubic programme that I believe is necessary to run an RSP under Linux.
I chickened out and use windows.
Search found 355 matches
- Sat Dec 02, 2017 7:12 pm
- Forum: New Users' experiences
- Topic: Can't connect to my RSP1A (Linux, command line)
- Replies: 10
- Views: 35409
- Thu Nov 30, 2017 10:02 am
- Forum: SDRuno
- Topic: Old to RSP1, new to SDRuno, need help!
- Replies: 6
- Views: 16704
Re: Old to RSP1, new to SDRuno, need help!
OK, I'll take a shot at some of your questions..... If you are using version 1.21, that may be the same issue I have encountered and reported on an open support ticket. It has happened to me twice but I have not found a way to duplicate it at will. The software acts as though the LO is locked even ...
- Wed Nov 29, 2017 9:12 am
- Forum: SDR Antennas
- Topic: Antenna port limitations
- Replies: 1
- Views: 11182
Antenna port limitations
Having had the RSP2 for a whiie now and achieved generally pretty satisfactory results with the antenna setup that is possible/practicable for me at present, which is: Longwire on the Hi-Z Port, H/V/UHF Discone (with some HF capability) on Port B and an active mini-whip on Port A. Whilst I note that...
- Sun Nov 26, 2017 8:00 am
- Forum: General
- Topic: RSP2Pro, SPRUno, and the Mac
- Replies: 2
- Views: 8914
Re: RSP2Pro, SPRUno, and the Mac
Although primarily a Mac user, I use a PC for SDRuno and the RSP2. However, the link below takes you to the SDRplay downloads page where the necessary software to run them on a Mac is located. https://www.sdrplay.com/downloads/ I understand that it can be run successfully using Cubic, although some ...
- Sat Nov 25, 2017 2:01 pm
- Forum: SDRuno
- Topic: New User Problems
- Replies: 18
- Views: 44537
Re: New User Problems - frequency entry
Please note that there is a "." top left on the uno keypad and "mhz" top right.
So, enter whole Mhz - tap dot - complete entry - tap Mhz.
It is in the revised manual....
So, enter whole Mhz - tap dot - complete entry - tap Mhz.
It is in the revised manual....
- Mon Nov 20, 2017 12:17 pm
- Forum: General
- Topic: NDB reception
- Replies: 12
- Views: 41739
Re: NDB reception
Hi 13dka Thanks for all the information. Were I to "sacrifice" the HI-Z port to achieve the best LF/mf signal on the mini-whip (which definitely outperforms my simple end-fed long-wire in this area), I would disadvantage myself with respect to reception on the long wire (9:1 balun in line) and not b...
Re: Scanner?
Just for the record; I tried the RSP2 and EXTIO version with the SDR# revision 1361, which ran as advertised (when I finally cornered a copy). However, I was unable to locate the Frequency Manager plug-in that works with this version, so abandoned this route. Happy for now to wait for the real deal,...
- Sun Nov 19, 2017 9:22 am
- Forum: General
- Topic: NDB reception
- Replies: 12
- Views: 41739
Re: NDB reception
Hi Andy Thanks for all the useful advice re NDB reception. Did a bit of antenna "fettleing," replacing the RAS0Ms mini-whip on port A with another version from the Ukraine (I doubt my ability to make my own) and using it on Port A, I am now able to get pretty good NDB reception (mainly using your pr...
Re: Scanner?
Hi there If it would be of any assistance to you in coming to a decision, both the RSP1 and apparently the RSP1A are able to scan using the well-thought of and featured SDR# programme, which is available as a plug-in via the downloads section of the SDRplay website - see: http://www.sdrplay.com/down...
- Wed Nov 15, 2017 11:04 am
- Forum: SDRuno
- Topic: SDRuno 2.1
- Replies: 2
- Views: 7679
Re: SDRuno 2.1 - bit of a wait for this one?
Sorry - dyslexia
Thanks very much for all the hard work with the latest 1.21 version and all the hard work involved in such a short time frame -much appreciated.
If I can't even get the version right what hope is there?
Thanks very much for all the hard work with the latest 1.21 version and all the hard work involved in such a short time frame -much appreciated.
If I can't even get the version right what hope is there?