Search found 136 matches

by mikeladd
Mon Jul 15, 2019 9:37 pm
Forum: New Users' experiences
Topic: adjust bandwidth for WFM
Replies: 5
Views: 232

Re: adjust bandwidth for WFM

I have found the default volume level in Uno to be good. If you crank it near max it will distort. I have my Windows output volume at 100%
I leave Uno's volume alone and adjust my speakers volume as needed.
by mikeladd
Mon Jul 15, 2019 7:32 pm
Forum: New Users' experiences
Topic: adjust bandwidth for WFM
Replies: 5
Views: 232

Re: adjust bandwidth for WFM

When I listen to FM broadcast stations 87.9–107.9 I use ZERO IF mode (MAIN panel) @ 5 Mhz of bandwidth with the RF GAIN at max. I give myself separation between the TUNE and the LO I set the RX control for FM/SWFM/192k. If the station is weak but in Stereo. I use the FMS noise reduction from the EX ...
by mikeladd
Wed Jul 10, 2019 1:13 pm
Forum: New Users' experiences
Topic: can't get sdrplay to work with e4000 2832 dongle
Replies: 5
Views: 252

Re: can't get sdrplay to work with e4000 2832 dongle

The e4000 2832 dongle is RTL based so you will need to use the associated EXT/IO dll driver placed in your My Documents folder. http://www.hdsdr.de/hardware.html To use SDRuno with this device, you must use SDRuno v1.22 https://www.sdrplay.com/downloads . This version of SDRuno has two editions. You...
by mikeladd
Sun Jul 07, 2019 12:55 am
Forum: SDRuno
Topic: make sdruono easier to read
Replies: 2
Views: 288

Re: make sdruono easier to read

I forgot to add the following that SDRuno auto populates its panels based on preset resolutions. This is valid only for an unaltered "default" workspace. Which is workspace 0 Try the following. Lower your system resolution Launch SDRuno Select an unused Workspace from the MAIN panel. 1-9 Y...
by mikeladd
Sat Jul 06, 2019 11:40 pm
Forum: SDRuno
Topic: make sdruono easier to read
Replies: 2
Views: 288

Re: make sdruono easier to read

You can try lowering your systems display resolution.
by mikeladd
Sat Jul 06, 2019 7:26 pm
Forum: Rig Control
Topic: SDR Uno control of Icom icr5600
Replies: 1
Views: 885

Re: SDR Uno control of Icom icr5600

You sure the model you have listed in your query is correct? I can't find anything on an Icom ic-r5600
by mikeladd
Sat Jul 06, 2019 1:20 pm
Forum: General
Topic: RSPDuo overload warning Help needed.
Replies: 1
Views: 271

Re: RSPDuo overload warning Help needed.

ADC Overload means the ADC is getting too much signal. That doesn't mean you will fry the input of the RSP. As long as the signal doesn't exceed the safe range the RSP is fine. +10 dBm (10mW) for short durations and 0 dBm (1mW) continuous.
by mikeladd
Sat Jul 06, 2019 1:12 pm
Forum: SDRplay related
Topic: Bias tee
Replies: 8
Views: 535

Re: Bias tee

In SDRUNO it is via the MAIN panel
https://www.sdrplay.com/docs/SDRplay_SD ... Manual.pdf

In SDR-Console it is via the HOME tab

In HDSDR it is via the RSP EXT/IO panel
https://www.sdrplay.com/docs/sdrplay_ex ... _guide.pdf
by mikeladd
Sat Jul 06, 2019 1:09 pm
Forum: Rig Control
Topic: Ham Radio Deluxe, SDRUno and TS-590sg help
Replies: 3
Views: 589

Re: Ham Radio Deluxe, SDRUno and TS-590sg help

VSPE has a software splitter. I have used this option in the past without issues (SDRuno,ACL logger & Omnirig).
COM0COM only creates a pair but VSPE has so much flexibility
http://www.eterlogic.com/Products.VSPE.html
by mikeladd
Sat Jul 06, 2019 2:08 am
Forum: Rig Control
Topic: Yaesu FT2000 synchronize with SDRUno
Replies: 2
Views: 2125

Re: Yaesu FT2000 synchronize with SDRUno

Have you followed the setup video and PDF guide?

Video is here
https://www.youtube.com/watch?v=fIDoNpLQ3MA

Guide is here
https://www.sdrplay.com/docs/HRDandSDRuno.pdf

If your using apps that need the same com port, You will need VSPE and setup a "splitter" in VSPE.

Go to advanced search