Search found 325 matches

by Paul
Sun Jun 16, 2019 7:14 am
Forum: General
Topic: Adjusting volume in scanner...
Replies: 4
Views: 303

Re: Adjusting volume in scanner...

Thank you for your kind response Gianfranco.
For some reason simplicity comes easily to me ;)
by Paul
Fri Jun 14, 2019 6:20 am
Forum: SDR Antennas
Topic: Receive Antenna & Impedance "Matching"
Replies: 63
Views: 4366

Re: Receive Antenna & Impedance "Matching"

Thank you both for your posts on this topic, which I have been following with interest. Whilst I lack the knowledge, capabilities and equipment to exploit your findings and conclusions properly, it has been most interesting, informative and the dialogue understandable even for the likes of me. The g...
by Paul
Tue Jun 11, 2019 10:13 am
Forum: New Users' experiences
Topic: Best antenna no good signals?
Replies: 7
Views: 527

Re: Best antenna no good signals?

Hi K9zip, if you have the room for a 33 foot long wire then you just may have room for a triangular shaped wire instead, ie. a horizontal delta loop, where the two ends come back to your feed point. You then use any form of twisted or parallel pair of wires as a feedline right down to your radio if...
by Paul
Tue Jun 11, 2019 7:42 am
Forum: SDRuno
Topic: V1.31 ANOMALY
Replies: 2
Views: 244

Re: V1.31 ANOMALY

Dear Support So it's worth having a look in the ini file (%appdata%\SDRplay\SDRuno.ini) to see if your preset is there under INST0 or INST1 etc. Secondly, I'm not sure what you mean about associating memory panels to presets? The active memory panel is what is used for all scans, so it's not surpris...
by Paul
Mon Jun 10, 2019 3:51 pm
Forum: SDRuno
Topic: V1.31 ANOMALY
Replies: 2
Views: 244

V1.31 ANOMALY

Starting point: Slave Receiver Scanning Mode custom presets #1 - 3 set up and renamed. Worked faultlessly for some time. However the renamed custom preset #3 has disappeared. The memory file associated with it remains in the assigned documents folder. I have assigned the preset details to custom pre...
by Paul
Fri Jun 07, 2019 3:18 pm
Forum: General
Topic: PRACTICAL PC CAPABILITY GUIDELINES FOR RSP OPERATION
Replies: 8
Views: 676

Re: PRACTICAL PC CAPABILITY GUIDELINES FOR RSP OPERATION

Of course Gianfranco (if I may use your name)
The intent of your post was quite clear and I merely offered mine as "additional" information for whatever use it might be should anyone experience similar problems.
by Paul
Fri Jun 07, 2019 9:25 am
Forum: General
Topic: PRACTICAL PC CAPABILITY GUIDELINES FOR RSP OPERATION
Replies: 8
Views: 676

Re: PRACTICAL PC CAPABILITY GUIDELINES FOR RSP OPERATION

Hi there I deleted my previous "reply" as being too lengthy and detailed. May I offer a sort of addendum to the forgoing post by glovisol. I was using a laptop with a spec which certainly exceeded the forgoing minima, using Windows10 and SDRuno to run a RSPduo together with a RSP2 and simu...
by Paul
Wed Jun 05, 2019 5:57 am
Forum: General
Topic: Adjusting volume in scanner...
Replies: 4
Views: 303

Re: Adjusting volume in scanner...

glovisol is absolutely correct of course and until now this what I have always done. However, out of curiosity, I have tried the computer main audio volume control, easily accessible either via taskbar, or keypad, which works without pressing the "stop," or interfering with the scan proces...
by Paul
Sun Jun 02, 2019 5:54 am
Forum: General
Topic: Parting thoughts
Replies: 16
Views: 1377

Re: Parting thoughts

For (the probably sadly departed) Noel Your inputs were obviously appreciated by some, including myself and I would like to say thank you for them. They were well written and obviously interesting to some of us who cared to read them. I was under the impression that one could choose to read, or not,...

Go to advanced search