Search found 499 matches
- Fri Mar 15, 2019 7:24 pm
- Forum: SDRuno
- Topic: 1.3 Unable to select WFM and SWFM
- Replies: 7
- Views: 23475
Re: 1.3 Unable to select WFM and SWFM
Please ensure that you have a high enough final sample rate. It is not possible to select to select a demodulation bandwidth that is greater than the final sample rate you have set. There is no problem with either WFM or SWFM in release 1.3 as long as have a high enough final sample rate and this ha...
- Fri Mar 15, 2019 5:12 pm
- Forum: SDRuno
- Topic: Scanning the 2M Ham band
- Replies: 7
- Views: 25626
Re: Scanning the 2M Ham band
Hello VE9DAN, You don't say what your noise floor or your threshold setting is. The only correct way to measure the noise floor is via the power meter when the VFO is placed in a quiet area of the band. Also, don't forget that you need set up your demodulator mode and bandwidth before starting the s...
- Thu Mar 14, 2019 9:30 pm
- Forum: SDRuno
- Topic: Bandwidth selector gone in 1.3
- Replies: 2
- Views: 9247
Re: Bandwidth selector gone in 1.3
Hello Malmen, This simply means that SDRuno is in low IF mode. Have a look at the main panel and it will indicate Low IF. A number of the band framing buttons now use Low IF by default, because it minimises the spurious mixing products that can occur in the lower bands. Also the scanner also uses lo...
- Thu Mar 14, 2019 8:11 pm
- Forum: SDRuno
- Topic: SDRuno Rel 1.3 Memory Scanning
- Replies: 3
- Views: 15287
Re: SDRuno Rel 1.3 Memory Scanning
Hello G8PTN, The most effective way to use memory panel scanning is to organise frequencies of interest into a range of memory banks, where the frequencies in each bank are all within the same band using the same modulation type and bandwidth. Also for speed of scanning, it makes sense to order them...
- Thu Mar 14, 2019 3:07 pm
- Forum: SDRuno
- Topic: 1.3 installation
- Replies: 7
- Views: 18239
Re: 1.3 installation
Hello cmh31909, There Is no way to do what you ask. The new way of saving settings maps all settings to a specific device unless it is a RSP1. So if you have two RSP2s and use them for different things with SDRuno with different settings, the .ini file will preserve settings for a specific device. M...
- Thu Mar 14, 2019 3:02 pm
- Forum: SDRuno
- Topic: 1.3 installation
- Replies: 7
- Views: 18239
Re: 1.3 installation
Hello Patrick,
There is no mandatory sequence. Installing SDRuno will install the new API anyway.
Sincerely
Tech_Support
There is no mandatory sequence. Installing SDRuno will install the new API anyway.
Sincerely
Tech_Support
- Thu Mar 14, 2019 1:13 pm
- Forum: SDRuno
- Topic: 1.3 installation
- Replies: 7
- Views: 18239
Re: 1.3 installation
Hello Patrick,
I am afraid not. All settings are saved in a .ini file and the settings are now device dependent, so this is a completely different approach to when the setting were saved in the registry.
Sincerely
Tech_Support
I am afraid not. All settings are saved in a .ini file and the settings are now device dependent, so this is a completely different approach to when the setting were saved in the registry.
Sincerely
Tech_Support
- Mon Mar 11, 2019 8:36 am
- Forum: SDRuno
- Topic: Error Msg Re _api_Service Not Responding ?
- Replies: 1
- Views: 7410
Re: Error Msg Re _api_Service Not Responding ?
Hello Bob,
Close down SDRuno. Navigate to the SDRuno installation directory and un the 'RestartService' batch file. Then try to restart SDRuno.
Sincerely
Tech_Support
Close down SDRuno. Navigate to the SDRuno installation directory and un the 'RestartService' batch file. Then try to restart SDRuno.
Sincerely
Tech_Support
- Wed Mar 06, 2019 10:19 pm
- Forum: SDRplay related
- Topic: New User just a little moan :(
- Replies: 1
- Views: 9544
Re: New User just a little moan :(
Hello Delecky,
Release 1.3 (with scanning) is in final beta test with the last couple of bugs being ironed out. It will be release very soon.
Sincerely
Tech_Support
Release 1.3 (with scanning) is in final beta test with the last couple of bugs being ironed out. It will be release very soon.
Sincerely
Tech_Support
- Wed Mar 06, 2019 12:08 pm
- Forum: SDRuno
- Topic: SDRuno on Linux
- Replies: 26
- Views: 89194
Re: SDRuno on Linux
Hello again StandingWave, When you try to change the IP address in the ExtIO Window, it is important to ensure that 'Auto Reconnect' and 'Persistent Connection' options are UNCHECKED before you try to change the IP address. If either of these options were checked, I recommend that you uncheck them a...