Powered by ZigaForm version 3.8.9.4

Latest Stable Version of SDRuno is 1.33

(25th November 2019)

Release Notes:
Release notes for all versions of SDRuno can be found by clicking here

Known Issues:
• SP2 CWAFC drift issue (Zoom/window size/freq display)
• IF output mode disabled SP1 spectrum mouse clicks
• ADC OVERLOAD may appear “stuck”. If Stop/Play does not clear, close and restart SDRuno
• PWR/SNR to CSV may have missing entries

Note: the known issues will be addressed in future versions of SDRuno. The effect of the IF output mode issue, is that you will NOT be able to click on the spectrum to select the tunable frequency with the mouse pointer. You will ONLY be able to either use the mouse scroll wheel (or other scrolling device) or the direct frequency input method.
In downloading this software, you understand and accept that the issues above are temporary and will be addressed in a future release.

The auto update feature will prompt you to update your installation to this latest release. To prevent that message from appearing when you start SDRuno, click on OPT in Main Window and uncheck “Enable Auto Update Check”

SDRuno 1.4 Release Candidate 2

(8th June 2020)

Warning: This is un-released software and you install it in the knowledge that it will have bugs and issues. We are looking for feedback on this version as we move towards the full release of 1.4

Before installing 1.4 RC2, we recommend that you create a backup copy of your SDRuno.ini file. To do this open Windows Explorer and enter %Appdata%\SDRplay in the address bar. This will open the folder where the SDRuno.ini file is stored. Copy this file to a new file named SDRuno_bak.ini. This will create a backup of your .ini file, which meas that should you need to reset it in the future, you will always be able to restore the position you were at before installing v1.4 RC2

Important Information
• The API installer may take some time to complete due to the installation of the Microsoft VS2008 redistribution package. Do not cancel the installation and wait for it to complete.
• The plugin system has only been tested on Windows 7 and Windows 10 – feedback on other versions of Windows, from XP to Vista would be very useful.
• The plugin window frames look different between Windows 7 and Windows 10 (possibly will be on other versions of Windows as well) – we will address this in a future update of the plugins.
• This version of SDRuno will install API 3.07 of the API – this may make other software that have been designed to work on 3.06 or below to not work. Reinstall SDRuno 1.33 to put API 3.06 back on the system. Note, API 3.06 and API 3.07 cannot co-exist on the same system, so you will need to be mindful of that when deciding what version of SDRuno you want to use.

Things we are already aware of and will be addressed before final release:
• Selecting band frame, then unframing band and scrolling the RF frequency < 2 MHz can cause strange behaviour (not readily repeatable).
• Start SDRuno without ini file and go to band frame does not allow the RF frequency to be changed (not readily repeatable).
• Start SDRuno without ini file and go to HDR mode (LW or LOW) = no signal. MW is ok.
• Leaving DAB mode leaves IFAGC and Audo LO mode disabled.
• Leaving DAB mode and going to HDR can lose RF gain control.
• SP1 frequency display can be “dragged” and cause the spectrum display to “wrap around”.
• Starting a 2nd instance of SDRuno with only 1 RSP connected causes it to crash.
• Extra error reporting to be added to the status bar.
• Status bar debug messages to be removed.
• Memory panel filter column is not an editable field in SDRuno.
• Plugin windows ALWAYS stay on top of all other windows.
• Plugin Control panel sometimes disappears below other SDRuno panels.
• Power/SNR output to file sometimes skips entries.
• S-Meter in T-Mate2 controller does not correctly display below 30 MHz
• When switching to diversity mode, the IF mode can display ZIF in the main panel (not a functional issue).
• Memory panel does not prompt to save a changed file when switching banks.
• Sometimes the IFMODE button and text can be missing when not in band frame
• The user manual is being updated.
• DAB Plugin – DAB+ playback stutters after a short period of time

Release Notes:
Release notes for all versions of SDRuno can be found by clicking here

Note: the known issues will be addressed in future versions of SDRuno. The effect of the IF output mode issue, is that you will NOT be able to click on the spectrum to select the tunable frequency with the mouse pointer. You will ONLY be able to either use the mouse scroll wheel (or other scrolling device) or the direct frequency input method.
In downloading this software, you understand and accept that the issues above are temporary and will be addressed in a future release.

Feedback on this release candidate version can be sent to feedback@sdrplay.com – please note that all feedback will be read but we are unable to reply to all messages received. We may contact you if we need clarification on an issue you have reported.